Easy Kobo Case Tutorial

We got my Grandpa a new Kobo for Christmas, as his other one had been well used for a few years and didn't work anymore. His new one didn't fit in his other case, so this week when I saw him pull it out of a plastic bag, I decided I better make him a new one.

Since it was a quick and easy project, using materials I already had on hand, I thought I'd do a step-by-step tutorial for anyone who may be new to sewing and might want to make their own case!

Materials:

2 coordinating fat quarters (or scraps)

coordinating thread

batting

small hair elastic

button

Tools:

cutting mat

rotary cutter

ruler

chalk pen

pins

iron

ironing board

sewing machine

scissors

To calculate the size:

He told me his Kobo was about 5 1/8” x 7” and 3/8” deep. For the width, I rounded the 5 1/8” up to 5 1/4”, plus 1/4” to account for the depth, 1/2” to account for the seam allowance and 1/4” to add a little wiggle room. For the height, I took the 7”, added 1/4” to account for the depth, 1/2” to account for the seam allowance and 1/2” so that the Kobo wouldn’t be poking out of the top of the case. In simpler terms:

width of device + depth of device + seam allowance + 1/4” = width of rectangle

height of device + depth of device + seam allowance + 1/2” = length of rectangle

We also bought him a stylus to make it easier to use the new touch screen, so I added a pocket to the case. It is the same width as the other rectangles, and about half the height. 

Steps:

If you plan on being able to wash the case, pre-wash your fabric so that it won't shrink on you later. Press your fabric before you start. 

Using a cutting mat, rotary cutter and ruler, cut (x 2) rectangles of your lining fabric, (x 2) rectangles of your outside fabric and (x 2) rectangles of your batting. Mine were 6 1/2” x 8 1/4”. For the pocket, cut (x 1) rectangle from your lining fabric and (x 1) rectangle from your outside fabric. Mine were 6 1/2” x 4 1/4”. 

Put the batting on the wrong side of your outside fabric. Using your ruler, mark a line 1 1/4" from the long edge of your fabric with a chalk pen. Sew along the line. Using a 1/4" foot on your sewing machine, sew three lines parallel to your first line. Repeat with your other outside piece and the outside pocket piece. Note that for the pocket piece, you are just sewing the lines on the one piece of fabric, without batting. Trim your batting when finished if needed. 

Pin the two lining pieces, right sides together and sew along the sides and bottom, using a bit more than a 1/4" seam allowance. Because the lining piece will be inside batting, which is bulky, a generous seam allowance will make the lining slightly smaller than the outside, which will help it fit a bit better and will help when you attach the top later. Leave about a 2" gap along one side. This will allow you to turn your case right-side out later. Clip your bottom corners, being careful not to cut into the sewing. This makes your corners less bulky when you put the case together. 

Pin your lining pocket piece and your outside pocket piece, right sides together and sew along the top with 1/4" seam. Press the seam, turn it right-side out and press again. 

Starting 1/4" from the edge, sew a line along the top edge of the pocket. Sew 3 more parallel lines. Place your pocket piece on top of one outside piece, lining up your sewn quilting lines. Pin it in place. 

* If you're afraid it will move, you could baste the pocket onto the outside, by using a longer stitch and sewing about 1/8" from the edge along the sides. I chose to just pin it. 

Place your other outside piece on top, right sides together. Match up your quilting lines. Pin it in place. I left the pins in from my pocket and just left them sticking out, that's why the sides on the bottom half seem to have lots of pins. 

Sew along the sides and bottom, using 1/4"seam allowance. Clip the bottom corners to reduce the bulk and help them turn better.

*Here, I also trimmed the batting and the fabric in the seam to reduce the bulk. If you choose to, just be careful not to trim it too close your sewing line. 

Turn it right-side out. If you pinned it well and sewed your lines evenly, they should match up. If not, who cares, don't worry about it. 

The sun came out for this picture and it's time to attach the button! I hand sewed this part because I decided it was faster than remembering how to use my button foot. Sew your button to the front (pocket side) of your case, in the middle about 3/4" from the top edge. 

On the back, pin a small hair elastic in the centre, about 1/4" from the top, with about 1/4" sticking out. I pinned from the inside and then slid the elastic through it. Sew the elastic to the case, about 1/8" from the edge. I used the finishing stitch function on my machine a couple times so that it sewed back and forth over the elastic. You could sew a few stitches forward, then a few stitches backward and repeat a few times as well. 

*You could use other elastic, but I had a new pack of hair elastics and they were the perfect size and shape. 

*You could also hand sew this part if you aren't as comfortable with your machine.

These stitches will help secure the elastic, but they'll be hidden in the seam, so it doesn't matter if they're pretty. 

Place the lining piece around the outside piece, so that the right sides are together and the outside piece is on the inside. Pin around the top edge, lining the side seams up. Sew 1/4" around the top. Be sure to backstitch at the beginning and end of your stitching. 

*You may have to take a piece off of your machine so that you can fit the case over your machine, making it easier to sew through one layer, without catching the other side. 

Turn your case right-side out, pulling the outside fabric through the hole you left in the lining. 

It should look like this when you're done turning it right-side out. Hand stitch the opening in the side of the lining closed to finish it off. 

Push the lining in and you're finished! Normally I would press and topstitch around the top edge, but it would have ruined the effect of my quilting lines, so I left it. 

Upon delivery, I was happy to see that the Kobo fit in the case and the elastic fit nicely around the button too. Grandpa's stylus fit either horizontally or vertically in the pocket too. I think if I was making another one I might make the pocket 1" taller for the stylus. 

Overall, the Kobo case was simple to put together and only took a couple hours to sew - and that was with switching rooms to take pictures. I think this case would work for any tablet, e-reader or smartphone, all you would have to do is change the dimensions. I used a quilting cotton for the inside and some sort of stretch chambray for the outside, but you could use other types of fabrics as well. If I was making one for myself, I would definitely use a bright lining! You could also change the quilting lines or pocket to further personalize it. 

I hope this tutorial was helpful. If you have any questions, you can leave a comment or send me an email. If you make your own, send a picture!

Happy sewing!

I'm linking up at Show and Tell Tuesday